MOTHERBOARD INSTALLATION TIPS
Install the motherboard is not something that sulitn but need only require accuracy and willpower. To do these things to note are: 1. Special attention to the jumpers.
Until now there is no standard layout for the jumpers on the motherboard. Because industrial motherboard manufacturer, has its own layout design. Although not prominent among their respective manufacturer. However, for the first time you install a new motherboard, we recommend reading the manuals. Because not all motherboard products, has shown clear text explanation on the motherboard PCB. Do not second-guessing on this.
2. Screw technology.
Before installing the motherboard, most chassis equipped with a rather large screws. Optimize usage. Try all the motherboard installed fastener point screw hole. Thus, the motherboard can be installed with adhesive on the casing. But certainly not the origin pairs. Customize the length and size of screws used in accordance with holes.
3. Use the I / O Shield.
An iron plate that serves to close the gap there between the input / output connectors of the motherboard. With a pair of iron plates, in addition to the computer will look neat, the computer will also be more closed so as not accessible by dirt or insects.
4. Select the appropriate port.
The assumption that by putting the SATA or PATA drive into any connector will make your system can boot. Some motherboards provide a RAID controller for SATA / PATA. For this, requiring drivers who are usually included in a diskette. You must first install the new Windows XP you can boot.
5. Customize RAM.
If you install the first memory slot is blue, the second memory was not necessarily so. But what if the motherboard has four memory slots with the same color? If you do not get the proper configuration for the dual-channel memory, the system likely will experience significant performance degradation.
6. Use the appropriate power connectors.
In the latest release of motherboards using the connectors that are different from previous. Therefore, pairs all existing power connectors match those on the motherboard, you should never combine the two into a single power connector, because it can cause fatal damage.
7. Installation of the processor.
This is the hardest part in the installation of the motherboard. Because if you mistakenly put it not possible that your processor will be damaged. In the old motherboard, you need a screwdriver to release the tool hooks heatsink.
Until now there is no standard layout for the jumpers on the motherboard. Because industrial motherboard manufacturer, has its own layout design. Although not prominent among their respective manufacturer. However, for the first time you install a new motherboard, we recommend reading the manuals. Because not all motherboard products, has shown clear text explanation on the motherboard PCB. Do not second-guessing on this.
2. Screw technology.
Before installing the motherboard, most chassis equipped with a rather large screws. Optimize usage. Try all the motherboard installed fastener point screw hole. Thus, the motherboard can be installed with adhesive on the casing. But certainly not the origin pairs. Customize the length and size of screws used in accordance with holes.
3. Use the I / O Shield.
An iron plate that serves to close the gap there between the input / output connectors of the motherboard. With a pair of iron plates, in addition to the computer will look neat, the computer will also be more closed so as not accessible by dirt or insects.
4. Select the appropriate port.
The assumption that by putting the SATA or PATA drive into any connector will make your system can boot. Some motherboards provide a RAID controller for SATA / PATA. For this, requiring drivers who are usually included in a diskette. You must first install the new Windows XP you can boot.
5. Customize RAM.
If you install the first memory slot is blue, the second memory was not necessarily so. But what if the motherboard has four memory slots with the same color? If you do not get the proper configuration for the dual-channel memory, the system likely will experience significant performance degradation.
6. Use the appropriate power connectors.
In the latest release of motherboards using the connectors that are different from previous. Therefore, pairs all existing power connectors match those on the motherboard, you should never combine the two into a single power connector, because it can cause fatal damage.
7. Installation of the processor.
This is the hardest part in the installation of the motherboard. Because if you mistakenly put it not possible that your processor will be damaged. In the old motherboard, you need a screwdriver to release the tool hooks heatsink.
Subscribe to:
Post Comments (Atom)
sponsor link
YM
No comments:
Post a Comment